Friday, September 20, 2013

60's Mod Couch Reupholster -- Installment 7

Welcome! We are nearing the finish line on our sofa. In this installment we are going to put the cording on the bottom of our sofa and attach the dust cover to the bottom of our sofa.

First you'll need to measure around the entire bottom of your sofa to get the length of your cording. Remember the saying -- Measure twice, cut once! Add 5 inches to your measurement just in case. Since our couch was over 7 feet long I had a lot of cording to make! A LOT!!

To make your cording you'll first need the plain cord. (Sometimes called upholstery piping cord, welt cord.) We used 5/32" cord. Cut out a 2 1/2 inch wide strip of fabric to the length you need. Unless you have really long fabric you'll need to join strips together. Center your cord in the fabric and wrap your fabric around the cord. Use the proper size cording foot (you can also use a zipper foot) on your sewing machine and sew as close as possible to cording for the entire length. When you have all of your cording made cut off the excess fabric, leaving a 1/2 inch allowance. 

Take your cording and, starting in the back, staple it to the bottom edge of your sofa. Leave about an inch from the edge to the first staple.


When you go around the legs of your sofa cut off the excess, getting as close to the actual cording as possible.





Once you make it all the way around your sofa you'll need to join your cording together. To do this cut off most of the excess cording leaving about an inch overlap. Then take and use a seam ripper to rip the seam out, go back about two inches past where they overlap. Next take the actual cord and cut it as close as possible to where it will join with the other end. 


Then take the fabric from the piece you have cut and fold it over to make a nice clean edge.


Take the fabric on your loose cording and wrap it around the fabric on your stapled cording. Remember, you stapled back about an inch from the edge so you should have room to do this. Your cord ends should just about touch. If you find you left too much cord cut to adjust.


Next we are going to take a small strip of cardboard and staple it around our 1/2 inch seam on our cording. This is so that the cording allowance won't droop down and be seen. Now you are done with your cording. 



Next you will put the dust cover on the bottom of your sofa. We saved the dust cover that we took off the sofa but it smelled like it had been stored in a musty basement for YEARS so we opted not to use it. Instead, we used landscape fabric. Yep, you read that right, landscape fabric.

Measure, cut to size and staple on. You'll need to make careful cuts around your sofa legs. Bam! Dust cover complete.






Next installment we will make our cushions and complete our sofa!!!

Friday, August 30, 2013

60s Mod Couch Reupholster -- Installment 6

Last time we put on the inside back of our sofa. Today we are going to put on the outside arms and back of our sofa. 

Depending on the style of your sofa or your personal preference you may or may not want to put cording on the arms and back of your sofa. I decided I wanted cording on mine so the first thing we did was take our measurements for the cording. We measured up the arms and around and then across the back. It was a lot of cording! I'll explain in a later post how to make the cording but for now just know that you need to leave a 1/2 inch allowance on your cording. 

We stapled the cording around the sides and back of the sofa. When you get to the corners make a small cut in your 1/2 inch allowance to get a tighter fit around the corner. You can also use a pair of pliers to squeeze the fabric together if necessary to get an even tighter curve.



 Get it as close to the corners and edges as you can, try to keep a straight line (or follow curves if necessary). 



After you have your cording stapled on next you will want to staple on your Ply-Grip (also called Curve Ease). Of course if you aren't using cording you'll start with this step. Did you ever wonder how they get fabric on things without the staples showing? Ply-Grip!

In our case we butted the Ply-Grip up against our cording. Be sure to staple each hole in the Ply-Grip. This does take a little precision with the staple gun. You can see the little metal teeth that grab the fabric in the second photo.






You'll want to put any cotton batting on before you put your fabric in the Ply-Grip. For the outside of our sofa arms we had a thin piece of cardboard that reused from the original upholster (found when we took the sofa apart). And for the back of our sofa we ended up stapling a piece of cotton fabric cut from a bed skirt. (You could use any spare piece of fabric for this since it won't be seen.)



After you have your cotton batting in place, measure your fabric for the area you are covering. Remember when you measure and cut your fabric to leave two inches on each side! Put the outside arms on before you put on the back of the sofa. After you do the outside arms of the sofa you'll need to go back and staple more Ply-Grip down the back sides (by the arms) so the fabric on the back will have something to attach to on the side (the place where the back of the sofa joins the back of the arms).

For the Ply-Grip take the little metal teeth and bend them upwards at a 45 degree angle. Take a cake spatula and press your fabric into the valley you've created.


It should catch slightly on the little metal teeth. Once you've pressed in around all the sides take your scissors and angle them into the valley and very carefully cut off the excess fabric.



When you have the excess fabric cut off you'll need to take your hammer and hammer the little teeth flat. You already have them bent upwards so just hammer them flat, like you are hammering them closed. This will pull the fabric taut across the area.


On the sides and the top where the Ply-Grip butts against the cording use the flat spatula to get a nice tight, clean fit.



When you have all your Ply-Grip hammered down you'll need to staple your fabric to the bottom of your sofa frame. In other words, completely finish the outside sofa arms before you move to the back. Now you have finished the outside arms and back of your sofa!



Friday, August 16, 2013

60s Mod Couch Reupholster -- Installment 5

If you've been following along you'll remember that last time we put on the inside arms of our sofa. This time we are going to put on the inside back of the sofa (the part the cushions will be against).

Of course the first thing you'll do is measure the inside back of your sofa to know how big to cut your fabric. Remember to add two inches to each side. When you have your fabric cut lay it across the inside back of the sofa.

Here again you'll be making cuts to go around the sofa frame. Same as before you'll use the needle to get the angle of your cut. Cut one side at a time and staple (described below) then move to the other side and do the same.




When you have made your cuts to go around the top and the bottom frame, push the fabric through to the back so you can staple it to the frame.



Start in the middle of the side and staple out to the edges of the side. As always, staple a little out from the center and then move to the other side of the center. Staple one side completely and then move to the other side, make your cuts to go around the frame and repeat. For now don't staple the part of the fabric above where you made cut at the top. (We'll get that when we staple the top part of the inside back.) Next you'll move to stapling the top and the bottom. Same thing here, staple a little on the top, staple a little on the bottom, moving back and forth from side to side and top to bottom. The reason for all of this is moving back and forth is so that you can keep your fabric pulled tight and wrinkle free. The picture below shows the part of the frame where you will staple the top. Basically just pull it over the top and staple it to the piece of wood there. Staple it as close to the bottom of that part of the frame as you can. You'll need to staple cording here later and you don't want your staples to show.



The picture below shows where you will staple the bottom part to the frame. You don't have to worry so much about your stapling here, it will be hidden by the back of the sofa.


At the top where you made your cut you'll want to make a pretty fold and staple that down. The staples will hold the fold in place. In the picture below the fabric isn't stapled down yet so forgive the pucker, it is more to show the fold. Also: you might need to cut out a little of the extra fabric when you are making the fold. Just be sure and not cut too much out.



When you have your fabric stapled on all sides you'll want to cut off your excess.


And there you have the inside back of your sofa! (my apologies readers, I neglected to take a picture.)

Friday, July 26, 2013

60's Mod Couch Reupholster -- Installment 4

If you'll remember last time we put on our sofa decking. This time we are going to put on the inside arms of the sofa. We are changing the look of sofa arms - no more seam and cording running up the middle - so we needed to add more padding to each of the arms. We first took the staple gun and stapled the existing foam to the sofa frame.


Next we measured and cut a piece of foam to cover the wood frame arm visible in the picture above. When we had that cut we stapled it in place.


The arm already had foam on the inside so we left that as is.


We covered both of the inside arms in cotton batting.


We then measured and cut our fabric. Remember to add two inches to each side you cut. So here you'll add two inches to both of the sides, the top and the bottom. Place the fabric over the inside of the arm.


You can see we have the needle back out (being held in the photo above). You'll need to make a straight cut this time to go around the frame arm in the front and the back. The picture below shows you where you'll want to place the needle on the backside of the arm in front.


After you've made your cuts (remember front and back) next comes the fun part - stapling! Staple the same way as before. Start in the middle, go out a few on either side, then move to the bottom and do the same. After you've made a few staples in the bottom, move back to the top. Rinse, wash, repeat. Remember to pull your fabric tight and not make any wrinkles or puckers. Stop before you get to the front and back of the arms on the top since you'll be making special curves/folds there (see later in post). Since our sofa arm is curved at the top, we made cuts in the fabric to help it go around the curve.


When you've got the top (all except the very front and back) and the bottom stapled, move to the sides of arms. In back you'll need to make a special fold at the top. The style that you make this curve in is a personal preference. You can see in the picture below that we tucked our fabric under and stapled for our fold. Remember to staple back far enough to get the back of the sofa on.


The fold in the front is also a personal preference. We wanted a clean looking fold since the couch has straight lines. We had to fiddle with it many times to get it a way we liked it.




Once everything is stapled, go around and cut off the excess.


Ta-da! Now you're finished with the insides of the arms.
Join us next time for another installment of the sofa re-do!